LECTROSONICS DPR-A/E01
This unique digital plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. The DPR-A can tune in coarse or fine steps across the UHF television band from 470.100 to 614.375 MHz for the E01/A1B1 version and from 537.600 to 691.175 for the E01/B1C1 version, with a selectable output power of 25 or 50 mW. The purely digital architecture supports AES 256-CTR encryption for high level security applications.
The transmitter is specially designed with high efficiency digital circuitry for extended operating time on two AA batteries, with status indicated by a multi-color LED. An IR (infrared) port is included to simplify setup with IR enabled receivers. Updates can be made via SD card. The input amplifier uses an ultra low noise op-amp for quiet operation. It is gain controlled with a wide range, dual envelope limiter, providing over 30 dB of headroom above full modulation. A 24-bit A-D converter digitizes the audio, then filters out supersonic noise above 21 kHz.
The DPR-A has an external SMA antenna jack, which accepts Lectrosonics steel flex wire AMM or AMJ series antennas.
FEATURES:
- wideband UHF tuning range
- accepts microphone or line level signals
- selectable 5, 15, 48 volt phantom power
- selectable 25/50 mW RF output power
- adjustable low frequency roll-off
- powered by two AA batteries
- IR (infrared) port for fast setup
- remote controlled "dweedle" tones (audio tone set-up control)
- time code jam sync with <1PPM accuracy
- solid machined aluminum housing
- on board recording
- encryption 256 Bit AES, CTR Mode
TRANSMITTER:
- operating frequencies: DPR-A/E01-A1B1: 470.100 to 614.375 MHz and DPR-A/E01-B1C1: 537.600 to 691.175 MHz
- frequency selection steps: 25 kHz
- RF Power output: selectable 25/50 mW
- frequency stability: ± 0.002%
- digital modulation: 8PSK
- spurious radiation: US= Compliant with ETSI EN 300 422-1 v1.4.2
- equivalent input noise: -125 dBV (A-weighted)
- Input level: nominal 2 mV to 300 mV, before limiting / greater than 1V maximum, with limiting
- input impedance: 1K Ohm
- input limiter: Dual envelope type, 30 dB range
- gain control range: 55 dB in 1 dB steps, digital control
- modulation indicators: dual bi-color LEDs indicate modulation of -20, -10, 0, +10 dB referenced to full modulation / LCD bar graph
- encryption: AES 256-CTR (per FIPS 197 and FIPS 140-2)
- frequency response: 25 Hz to 20 kHz, (+0, -3dB)
- low frequency roll-off: adjustable for -3dB @ 25, 35, 50, 70, 100, 120 and 150 Hz
- input dynamic range: 110 dB (A), before limiting 125 dB (with full Tx limiting)
- controls & indicators: LCD w/membrane switches / LED audio level indicators
- audio Input jack: standard 3-pin XLR (female)
- phantom power: 5V @ 18 mA max., 15V @ 15 mA max. and 48 V @ 4 mA max., plus "OFF"
- IR (infrared) port: For quick setup by transferring settings from an IR enabled receiver
- antenna: external SMA antenna jack
- battery: Two 1.5 Volt AA (lithium recommended) battery Life: AA Lithium, 48v phantom power engaged: SCHOEPS CMIT 5U: 7h 25m / SCHOEPS CMC6-U/MK41: 7h 20m / SANKEN CS-1: 8h 0m
- weight: 221 grams
- dimensions: excluding antenna: 106.9 L x 41.1W x 35.0 H mm
- emission designator: 170KG1E
RECORDER:
- storage media: microSDHC memory card (HC Type)
- file format: .wav files (BWF)
- A/D converter: 24-bit
- sampling rate: 48 kHz
- recording modes/Bit rate: HD mono: 24 bit 144 kb/s
- input level: Dynamic mic: 0.5 mV to 50 mV / Electret mic: Nominal 2 mV to 300 mV / Line level: 17 mV to 1.7 V
- timecode connector: 3.5 mm TRS
- signal voltage: 0.5 Vp-p to 5 Vp-p
- Input impedance: 10 k Ohms
- accuracy <1 PPM with TCXO
- format: SMPTE 12M 1999 compliant
- frequency response: 25 Hz to 20 kHz, +0.5/-1.5 dB
- dynamic range: 110 dB (A), before limiting / 125 dB (with full Tx limiting)
- distortion: < 0.035%
- operating temperature range: Celsius: -20 to 50
| Brand | Lectrosonics |
|---|
