article code
Neumann TLM49 Set large diaphragm cardioid microphone, incl. EA3 elastic suspension, nickel
€ 1,500.00 Our Price € 1,239.67 Our Price

Studio microphone with retro look. Warm sound, optimized for vocal recordings. Uses the capsule of the legendary M 49 and U 47. Cardioid polar pattern. The TLM 49 is a large-diaphragm studio microphone with a cardioid directional characteristic and a warm sound which is especially optimized for vocal performance. It is supplied as a set, with an elastic suspension. The design is inspired by that of the legendary M 49 and M 50 microphones of the 1950's. Naturally the TLM 49 has the typical Neumann fine matte nickel finish. The "sound design" is also oriented toward that of the M 49 and the U 47. By combining its retro look with proven Neumann transformerless circuit technology, this microphone ensures low self-noise and the use of high gain levels.

Applications: during the development phase, the sound was adjusted in extensive practical tests, so as to make the TLM 49 ideal particularly for vocal and speech recording. However, in addition, it is also suitable for instrumental applications in professional production studios and demanding home recordings.

Polar pattern: the large-diaphragm capsule of the TLM 49 provides a cardioid directional characteristic with a tendency toward supercardioid, due to the special capsule construction. Following the example of the M 49, high frequencies are more directional. The capsule diameter is 34mm. The front of the microphone is indicated by the red Neumann logo on the microphone body. The capsule is oriented so that the microphone is addressed from the front.

Acoustic features: the TLM 49 uses the famous K 47 capsule, which was also used in the M 49 and the U 47. The capsule has a linear frequency response up to the upper mid-range. Above 2kHz there is a gentle presence boost up to 3dB.

The capsule is enclosed by a large microphone headgrille, which is acoustically very open and is hence neutral with regard to the sound.

Electrical features: the letters TLM stand for "transformerless microphone". With TLM technology the usual output transformer is replaced by an electronic circuit. As with traditional transformers, it ensures good common mode rejection, and prevents RF interference that may influence the balanced audio signal. Noise signals which affect the balanced modulation line are therefore effectively suppressed. The microphone can operate at sound pressure levels of up to 129dB without distortion, and provides a dynamic range of 117dB (A-weighted).

Operational safety: the entire interior structure is mounted elastically, to prevent the transmission of structure-borne noise. In addition, the capsule is mounted with a rubber shock mount. Due to the wide frequency response, the TLM 49 can also transmit extremely low-frequency signals without coloration. Of course this means that the microphone is also sensitive to noise signals such as vibration noise and wind noise in this frequency range. The TLM 49 is therefore supplied with the elastic suspension EA 3, which effectively protects the microphone from structure-borne noise. If the microphone is addressed at extremely close range, pop screen PS 15 or PS 20 a can be used in front of the microphone to provide protection against plosive sounds.


  • same capsule as legendary Neumann U 47 and M 49 microphones
  • cardioid pattern
  • classic sound for silky vocals
  • large, acoustically open headgrille
  • transformerless solid state circuit with tube sound characteristics
  • very low self-noise

  • acoustical operating principle: pressure gradient transducer
  • directional pattern: cardioid
  • frequency range: 20Hz to 20kHz
  • sensitivity at 1kHz into 1 kOhm: 13mV/Pa
  • rated impedance: 50 Ohms
  • rated load impedance: 1 kOhms
  • equivalent noise level, CCIR: 23dB
  • equivalent noise level, A-weighted: 12dB-A
  • signal-to-noise ratio, CCIR (rel. 94dB SPL): 71dB
  • signal-to-noise ratio, A-weighted (rel. 94dB SPL): 82dB
  • maximum SPL for THD < 0.5%: 110dB
  • maximum SPL for THD < 5%: 129dB
  • maximum output voltage for THD < 5%: -1dBu
  • supply voltage (P48, IEC 61938): 48V (+/-4V)
  • current consumption (P48, IEC 61938): 3.2mA
  • matching connector: XLR3F
  • weight: 825g
  • diameter: 78mm
  • length: 165mm

More Information
1. Pick-up your order at our store.
2. Choose one of the different options from our shipping partners, presented to you during check-out.